Canon PIXMA MG2950 Wireless Connection Setup

Some access points (sometimes referred to as routers or hubs) feature an automatic connection button labelled “WPS” which st&s for Wi-Fi Protected Setup.

This allows permitted devices such as your PIXMA MG2950 to connect to your network without needing to enter a password & it enables a quick & easy method of connecting your devices.

This method is by far the easiest way of connecting your PIXMA MG2950 so if your access point has a WPS button please select the ‘WPS Connection Method’ tab below for instructions on connecting using this method.

If your router does not support WPS we have provided alternative instructions to get your PIXMA MG2950 connected so please select the 'Standard Connection Method' tab below.

WPS Connection Method

Before we start, there are some conditions that must be met in order to use the WPS push button method:

The access point must have a physical WPS push button available. Please check with your device’s user guide for details. If the WPS push button is not available please use the instructions on the Standard Connection Method tab.
Your network must be using the WPA (Wi-Fi Protected Access) or WPA2 security protocol. Most WPS enabled access points use this protocol
Make sure that the printer is turned on.
Press & hold the [Wi-Fi] button on the top of the printer until the orange alarm lamp flashes once & then release it.
Make sure that the Wi-Fi button starts to flash blue & then go to your access point & press the [WPS] button within 2 minutes. For exact details regarding pressing the WPS button, please refer to the access point manual.

The blue Wi-Fi lamp on the printer will continue ﬂash while searching for, or connecting to the access point. During the setup the green power lamp will also start to flash. When the printer has successfully made a connection to your wireless network, the blue & green lamps will stop flashing & remain lit.

To confirm that your printer is successfully connected to your wireless network, you can print out the network settings of your printer if you wish:
Make sure that your printer is turned on.
Load a sheet of A4 or Letter-sized plain paper.
Press & hold the [Cancel] button until the orange alarm lamp flashes 15 times & then release it. The network information page will be printed.
When referring to the printout, check that the “Connection” indicates “Active” & that the SSID -Service Set Identifier (or the name of your wireless network) indicates the correct name of your wireless network.

This concludes the WPS setup procedure.

Please now proceed by installing the software to make the most out of your PIXMA MG2950.

If you do not have the installation CD that came with your product, please download the manuals & software.

If the wireless setup is still failing after following this guide, please contact us for further assistance.

Standard Connection Method

Please use the links below to view the correct instructions for your operating system -

Standard Connection Method - For Windows users only

Insert the CD that came with your printer & run the setup. If the “Setup CD-ROM” does not autorun, insert the CD-ROM into the computer again & click on [My Computer] or [This PC], select the CD-ROM & double-click [MSETUP4.EXE]. If you do not have the CD (’s) that came with your product, please download the manuals & software.
When the initial screen appears, click on [Next].
Select [Wireless LAN Connection] as a connection method, then click [Next].
Select [Access Point Connection (recommended)] as the wireless LAN connection method then click [Next].
Ensure that your printer is turned on, make sure the green power lamp is on & then click [Next].
The software will now briefly search your network for any printers already connected. If this is the first time you are setting up your printer it will not be found. So please ensure that [Setting printer could not be found on the list] is selected, then click [Next].
The Setup Guide Installation will now start.
Click on [Next].
Click on [Cableless setup].
When the following screen appears, hold down the [Wi-Fi ] button (A) on the printer until the orange alarm lamp flashes 2 times & release after the second flash, then click [Next].
Make sure that the blue Wi-Fi lamp flashes quickly & the green power lamp is lit, then click on [Next].
The following message will be displayed
Once the connection to the access point is completed click [Next].
When the following screen appears, select your region & click [Next].
When the following screen appears, select your language & then click [Next].
When the following screen appears, select the software you wish to install, & then click on [Next]. If you’re not sure which software you want to install at this stage, don’t worry, as you can always uninstall it at a later stage if you wish.
When the following screen appears, click on [Yes] to agree to the end user license agreement.
When the following screen appears, click on [Next].
The software will now install. If the following screen is displayed during the installation, click on [Redetect] to search for your printer again. Depending on your network configuration, it may take a minute or so for the software to detect the printer. This may involve clicking on redetect a number of times.
Once the Cableless setup is complete the following screen will be displayed to indicate the model of your printer & the name (or SSID) of your wireless network. Click [Complete].
If this is the first time you are setting up your printer, when the following screen is displayed, click on [Execute] & follow the on-screen instructions to perform the print head alignment, otherwise click on [Next].
When the following screen is displayed click [Next].
If you wish to register your printer at this stage click [Next], alternatively you can register later using the Quick Menu software, so click [Cancel].
If you wish to take part in the Extended Survey Program click [Agree]. Alternatively, click on [Do not agree].
If the following screen is displayed & you would like to send a test print to your printer, click [Execute]. If not, click [Next].
Click on [Exit] to complete the installation.

This concludes the Windows setup
If the wireless setup is still failing after following this guide, please contact us for further assistance.

Cableless Setup method (For Mac users only)

Before you start please download the installation software.

Once downloaded, go to the location of the file & double click it. When the following screen is displayed, double click [Setup].
When the following screen is displayed, click [Open].
When the initial screen appears, click on [Next].
You may be asked to type in your password to continue with the installation. Type in your password & click on [Install Helper].
Click [Next].
Select [Wireless LAN Connection] as a connection method & then click [Next].
Select [Access Point Connection (recommended)] as the wireless LAN connection method then click [Next]
Ensure that your printer is turned on & the green power lamp is lit & then click [Next].
The software will now briefly search your network for any printers already connected. If this is the first time you are setting up your printer it will not be found. So please ensure that [Setting printer could not be found on the list] is selected, then click [Next].
If the following screen appears, select [Open].
Click on [Next].
Click on [Cableless setup].
When the following screen appears, hold down the [Wi-Fi ] button A on the printer until the orange alarm lamp flashes 2 times & release after the second flash, & then click [Next].
Make sure that the blue Wi-Fi lamp flashes quickly & the green power lamp is lit, & then click on [Next].
The following message will be displayed:
When the following message is displayed, click on [Allow].
Once the connection to the access point is completed click [Next].
When the following screen appears, select your region, & then click on [Next].
When the following screen appears, select your language & click [Next].
When the following screen appears, select the software you wish to install, & then click on [Next]. If you’re not sure which software you want to install at this stage, don’t worry, as you can always uninstall it at a later stage if you wish.
When the following screen appears, click [Yes] to agree to the end user license agreement.
Should the following screen appear, if you wish to create an alias of the manual on your desktop click [Agree], otherwise click [Do not agree] to skip.
The software will now download & install.
Within the Canon IJ Network tool screen select the detected printer & click [Next].
When the following screen appears, click [Add Printer].
When the following screen is displayed, select the [Canon IJ Network] version of your printer, & click [Add].
The following screen will briefly be displayed.
When the following screen appears, click [Next].
If this is the first time you are setting up your printer, when the following screen is displayed, click on [Execute] & follow the on-screen instructions to perform the print head alignment, otherwise click on [Next].
When the following screen appears, click [Next].
If you wish to register your printer at this stage click [Next], alternatively you can register later using the Quick Menu software, so click [Cancel].
If you wish to take part in the Extended Survey Program click [Agree]. Alternatively click [Do not agree].
Should the following screen appear, if you wish to perform a test print to confirm the network setup click [Execute], otherwise to skip this click [Next].
Click [Exit] to complete the installation.

This concludes the Mac setup

If the wireless setup is still failing after following this guide, please contact us for further assistance.

Restoring your PIXMA MG2950 network settings back to factory default

If you need to reset your network settings back to factory default, for example if you change your access point, you can do so by following these instructions:

Please note that initialisation erases all network settings on the machine, so printing or scanning from a computer over the network will become impossible until the printer is re-configured with new network settings.
Press & hold the [CANCEL ] button until the alarm lamp flashes 17 times.
Release the [CANCEL ] button.

The network settings have been reset back to factory default settings.

If this process is still failing after following this guide, please contact us for further assistance.

Source: canon-europe.com

Go to Link

Canon PIXMA MG2950 Wireless Connection Setup